Overview of ASME SA789 S32750 Aluminum 1060 Extruded Finned Tube
ASME SA789 S32750 Aluminum 1060 extruded finned tube is a premium bimetallic heat transfer component engineered for demanding chloride-rich corrosive environments. As a type of extruded finned tube, it separates the functional responsibilities of corrosion resistance and thermal conduction: the inner base tube handles pressurized corrosive process fluid, while the outer extruded aluminum fins deliver high air-side heat transfer performance. This design solves the common limitation of single-material heat transfer tubes, which struggle to balance high chloride resistance and excellent thermal conductivity. The product is widely adopted as super duplex finned tube for air cooled heat exchangers, seawater cooling circuits and sour service systems. It is also known as 2507 super duplex extruded finned tube in international heat exchanger projects.
This bimetallic construction is manufactured by cold extrusion forming. An aluminum 1060 sleeve is tightly fitted over the ASME SA789 S32750 seamless base tube, then rolled and extruded to form continuous spiral fins. The fins and aluminum cladding form a single integrated structure without welding or adhesive bonding. This characteristic keeps contact thermal resistance stable under repeated thermal cycling and mechanical vibration, which is critical for long-term reliability of S32750 bimetallic extruded fin tube in offshore and chemical cooling systems.
Core Definition of Key Terms
ASME SA789 S32750 (2507 Super Duplex Base Tube)
ASME SA789 is the ASTM specification for seamless and welded ferritic/austenitic duplex stainless steel tubes for general service. UNS S32750, commonly called 2507 super duplex, has a balanced austenite-ferrite microstructure close to 1:1 volume ratio. Its PREN value is higher than 41, delivering outstanding resistance to pitting, crevice corrosion and chloride-induced stress corrosion cracking. The yield strength is significantly higher than conventional austenitic stainless steel grades, which supports pressure containment for high-pressure process cooling loops.
Aluminum 1060 Extruded Fin
Aluminum 1060 is a commercial pure aluminum grade with minimum 99.6% aluminum content. It features high ductility suitable for cold extrusion and high thermal conductivity around 237 W/(m·K). The extrusion process creates DR-type integral fins, so the fin root remains solid and free of gaps that would degrade thermal performance. Aluminum 1060 is the preferred fin material for air-side heat transfer where oxidation and operating temperature stay within the allowable range.
Bimetallic Extruded Fin Tube
A bimetallic extruded fin tube combines two different metals, each selected for its own functional advantage. The inner alloy addresses fluid-side corrosion and pressure, while the outer fin material optimizes convection heat transfer with air or gas. This is the core principle behind S32750 Al1060 extruded fin tube for air cooled heat exchanger.
Key Parameters and Units
All values listed below are typical range. Final dimensions, mechanical limits and operating envelopes shall be confirmed by project specification, licensed heat exchanger engineer and manufacturer data.
| Parameter | Typical Range | Unit |
|---|---|---|
| Base Tube Outer Diameter | 19.05 ~ 50.8 | mm |
| Base Tube Wall Thickness | 1.65 ~ 6.0 | mm |
| Fin Height | 6 ~ 16 | mm |
| Fin Thickness | 0.4 ~ 0.5 | mm |
| Fins per Inch (FPI) | 7 ~ 11 | - |
| Maximum Single Length | ≤20 | m |
Material and Applicable Standards
| Component | Material Grade | Applicable Standard |
|---|---|---|
| Inner Base Tube | UNS S32750 (2507 Super Duplex) | ASME SA789 |
| Fin & Outer Cladding | Aluminum 1060 | ASTM B209 |
| Inspection & Documentation | Material Test Report | EN 10204 3.1 / 3.2, to be confirmed per project |
The base tube can be supplied with PMI verification, UT and ET non-destructive testing. Compliance with NACE MR0175 for sour service is available upon project request. All material acceptance criteria are subject to project specification.
Comparison Between Extruded Finned Tube and Other Fin Types
| Fin Type | Thermal Contact Stability | Vibration Resistance | Corrosion Risk at Root | Suitable for S32750 Base Tube |
|---|---|---|---|---|
| Extruded DR Fin (Al 1060) | Excellent | Excellent | Low | Recommended |
| L-footed Wrap Fin | Moderate, may degrade after cycling | Moderate | Medium | Conditional |
| Welded Fin | Stable | Good | High (weld zone) | Conditional |
For ASME SA789 S32750 extruded fin tube for seawater cooler, the extruded DR fin is preferred because the integral fin root avoids crevice gaps that trap chloride contaminants.
Design Tradeoffs and Selection Factors
Key Tradeoffs
- Fin height vs. air-side pressure drop: Taller fins increase heat transfer area but raise air-side pressure drop and fan power consumption. Fin height is normally limited to 16 mm for this grade combination.
- Galvanic corrosion risk: Aluminum and super duplex stainless steel have different electrode potentials. Continuous wet chloride immersion will create galvanic corrosion risk for the aluminum cladding. Surface coating or drainage design shall be evaluated if the unit runs in splash or continuous wet conditions.
Core Selection Factors
- Chloride concentration and fluid pH on tube side
- Maximum continuous operating temperature of air side
- Air-side fouling, dust and salt spray exposure
- Fan-induced vibration and cyclic thermal load
- Project requirements for material certification and NDT scope
Applicable Industries
This 2507 super duplex finned tube for chloride corrosion service is specified in these typical industrial sectors:
- Offshore oil & gas platform process cooling
- Seawater desalination and seawater cooling systems
- Chemical process plant acid brine cooling loops
- Flue gas desulfurization (FGD) cooling equipment
- Onshore sour gas processing facilities
Quality Inspection and Testing Items
Below is a typical inspection scope. Final test plan shall be aligned with project ITP and purchaser requirements.
- PMI positive material identification for S32750 base tube
- Ultrasonic testing (UT) and eddy current testing (ET) of base tube
- Dimensional check: OD, wall thickness, fin height, FPI, straightness
- Visual inspection of fin surface, fin root integrity and surface defects
- Material documentation review, EN 10204 3.1 or 3.2 certificate upon request
- Hydrostatic test of base tube as per ASME SA789
Packing and Shipping Requirements
Extruded finned tubes are vulnerable to fin deformation and surface scratching during transit. Typical packing measures include end caps for tube bores, separators between tube layers, wooden crates or plywood cases, and fixed strapping to prevent sliding.
Frequently Asked Questions
Need technical datasheet, customized dimension quotation or further discussion on ASME SA789 S32750 Aluminum 1060 extruded finned tube for your heat exchanger project? Request a Quote from Lordfintube.


